For quillers in India specially, things like Diamond Glaze are not easy to come by. So, here goes the process (specific to materials available in India, I'm sure quillers in other countries will be able to find analogues easily).
Step 1: Making the jewellery itself. It is an important step for making jewellery sturdy. You'll need to use your judgement in gauging whether the piece is sturdy. I am hopelessly obsessed with the jewellery being able to withstand stress (like my son pulling at my earrings). Make the piece "sturdy" before you think of water-proofing.
Step 2: Give a coating of a "water-soluble glue". It should at least be water soluble when wet. You can use Fevi-Gum (available for Rs. 5 in ANY stationery shop). Make sure you coat all crevices etc properly. Synthetic bristle brush works best, camel hair brush is a little difficult to handle due to variable length of the hair. Allow this to dry properly. I am biased towards Fevicryl Hobby Ideas Fabric Glue. It's more expensive but I prefer its consistency compared to Fevi-Gum (which I find more runny). But it's purely a personal preference.
Only glue coating is not likely to make the jewellery water-resistant as PVA (poly vinyl acetate) glue "swells" when in contact with water. It looks ugly to say the least, and the jewellery will be disfigured forever. Fevicryl Hobby Idea Fabric Glue however, is OK by itself. It still remains "sticky", so I won't recommend glue layer alone (unless you want all your paper jewellery to become ONE single lump, all earrings mating with each other! :D
Step 3: This is a crucial step and takes most time (not for coating, but for drying). Use a good lacquer varnish. My recommendation is Asian Paints Touch Wood. But practically any varnish should do. Again, use a synthetic brush to coat the jewellery. You WILL see some discolouration but don't worry, if you've done the glue coating properly, this discolouration usually vanishes after drying. Varnish needs overnight drying, so plan properly. If you are enthusiastic about a glossy finish, you can put 3-4 layers (which means coating them for 3-4 days). It lends a pretty (not my personal favourite still) glossy finish that is harder as well.
Please prepare properly for handling varnish (gloves if you are particular about not getting your hands smelly, I personally don't care). Work in a well ventilated (preferably with an exhaust fan) fan place. Use some organic solvent to clean the brush (kerosene works fine for me). Keep a scented hand-cream handy, you'll need it to get rid of the strong smell varnish will give to your hands. Try tying a wet cloth over your nose, organic solvents, when inhaled, are BAD for women of reproductive age (Be cautious).
I hope this is comprehensive enough. So, if you know someone who wants to how to make the jewellery water-resistant, please share this link. It is very difficult for me to write individually to people who ask. I end up feeling bad not replying.
Happy jewellery Making !!
Step 1: Making the jewellery itself. It is an important step for making jewellery sturdy. You'll need to use your judgement in gauging whether the piece is sturdy. I am hopelessly obsessed with the jewellery being able to withstand stress (like my son pulling at my earrings). Make the piece "sturdy" before you think of water-proofing.
Step 2: Give a coating of a "water-soluble glue". It should at least be water soluble when wet. You can use Fevi-Gum (available for Rs. 5 in ANY stationery shop). Make sure you coat all crevices etc properly. Synthetic bristle brush works best, camel hair brush is a little difficult to handle due to variable length of the hair. Allow this to dry properly. I am biased towards Fevicryl Hobby Ideas Fabric Glue. It's more expensive but I prefer its consistency compared to Fevi-Gum (which I find more runny). But it's purely a personal preference.
Only glue coating is not likely to make the jewellery water-resistant as PVA (poly vinyl acetate) glue "swells" when in contact with water. It looks ugly to say the least, and the jewellery will be disfigured forever. Fevicryl Hobby Idea Fabric Glue however, is OK by itself. It still remains "sticky", so I won't recommend glue layer alone (unless you want all your paper jewellery to become ONE single lump, all earrings mating with each other! :D
Step 3: This is a crucial step and takes most time (not for coating, but for drying). Use a good lacquer varnish. My recommendation is Asian Paints Touch Wood. But practically any varnish should do. Again, use a synthetic brush to coat the jewellery. You WILL see some discolouration but don't worry, if you've done the glue coating properly, this discolouration usually vanishes after drying. Varnish needs overnight drying, so plan properly. If you are enthusiastic about a glossy finish, you can put 3-4 layers (which means coating them for 3-4 days). It lends a pretty (not my personal favourite still) glossy finish that is harder as well.
Please prepare properly for handling varnish (gloves if you are particular about not getting your hands smelly, I personally don't care). Work in a well ventilated (preferably with an exhaust fan) fan place. Use some organic solvent to clean the brush (kerosene works fine for me). Keep a scented hand-cream handy, you'll need it to get rid of the strong smell varnish will give to your hands. Try tying a wet cloth over your nose, organic solvents, when inhaled, are BAD for women of reproductive age (Be cautious).
I hope this is comprehensive enough. So, if you know someone who wants to how to make the jewellery water-resistant, please share this link. It is very difficult for me to write individually to people who ask. I end up feeling bad not replying.
Happy jewellery Making !!
No comments:
Post a Comment